Page 2
Are there… ... any technical problems or other questions which you would like to be clarified? Please contact our help desk (see Warranty Booklet). The latest information on our products, tips, updates, etc., can be found on the internet under: http://www.fujitsu-siemens.com...
Page 4
This manual was produced by Xerox Global Services Published by Fujitsu Siemens Computers GmbH Order No.: A26361-K983-Z120-1-7619 Edition 6 AG 01/09...
Contents Introduction............................1 Notational conventions ......................... 2 Important notes............................. 2 Safety notes..........................2 Power cable..........................4 Transport ............................4 Cleaning ............................4 CE marking........................... 4 FCC Class B Compliance Statement ................... 5 Declaration of Conformity ......................5 Energy Star Guidelines......................... 6 Disposal and recycling .........................
A graphics card (screen controller) with VGA interface or a digital graphics card with DVI interface is required to control the SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S LCD monitor. The monitor processes the data supplied to it by the screen controller. The screen controller or the associated driver software is responsible for setting the modes (resolution and refresh rate).
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Notational conventions The meanings of the symbols and fonts used in this manual are as follows: Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data.
Page 11
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S ● To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must never be blocked. ● The monitor automatically sets itself to a mains voltage in the range of 100 V to 240 V. Ensure that the local mains voltage lies within these limits.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Power cable To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to replace the original cable set. ● The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S FCC Class B Compliance Statement The following statement applies to the products covered in this manual, unless otherwise specified herein. The statement for other products will appear in the accompanying documentation.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Energy Star Guidelines The Fujitsu Siemens LCD monitor SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S is designed to conserve electricity by dropping to less than 1 W when it goes into standby, suspend and OFF mode. With this new power management the LCD monitor SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S qualifies for the U.S.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Checking the contents of the consignment The display surface of the LCD monitor is sensitive to pressure and scratches. Always hold the device by the casing! ► Unpack all the individual parts.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Installing an ergonomic video workstation Avoid glare from electric Windows Edge of desk lighting. Permissible reaching Avoid direct and reflected glare. sector Position the keyboard where it is easiest to reach.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Mounting and removing the monitor base The display surface is susceptible to scratching! Therefore, lay the monitor on a soft surface when mounting or removing the monitor base. Folding out monitor base When delivered the lower part of the monitor base is folded up and secured to the monitor by a collar.
Page 18
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S ► Proceed according to the four steps in the illustrations to fold out the monitor base. A26361-K983-Z120-1-7619, edition 6...
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Removing monitor base Before you can use a swivel arm or a wall bracket, you must remove the monitor base: The display surface is susceptible to scratching! ► Switch off the monitor and pull the power plug out of the power socket.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Connecting cables to the monitor The monitor ports are protected by a cover. ► Remove the cover. P17-2 / P19-2 / P19-2P P20-2 / P20-2S On the P20-2 / P20-2S monitor, the DVI-D and D-SUB connectors (2 + 3) are the opposite way round.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S ► Insert one plug of the audio line in the AUDIO IN (5) socket on the monitor and make sure it is properly engaged. ► Plug the power cable supplied into the power connector (1) of the monitor.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Adjusting portrait format The monitor can be turned from the "wide format" (landscape mode) into the "high format" position (portrait mode). ► Grasp the monitor with both hands on the right and left edge of the casing, move it into the highest position and turn it clockwise until it is in the portrait position.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S When you switch the computer system on, you must proceed in the following order: ► First switch on the LCD monitor with the ON/OFF switch (2). ► Then switch on the computer.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Changing the monitor settings When putting the monitor into operation for the first time, the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Locking the OSD menu The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings. ► Press and hold the SELECT/MENU button for a few seconds while you switch on the monitor with the ON/OFF switch.
Page 26
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S The corresponding setting window (here: Image Adjust) is displayed (on the right-hand side). The first function (H-Position) is highlighted. ► If necessary, press the button to mark another function. ►...
Page 27
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Adjusting size and position Calling the Image adjust setting window Adjusting the horizontal position H-Position With this function you move the picture to the left or to the right. Adjusting the vertical position V-Position With this function you move the picture up or down.
Page 28
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Setting display of the OSD menu Calling the OSD Setup setting window Setting language for the OSD menu Language With this function you choose between English (default setting), French, German, Italian and Spanish as the language for the OSD menu.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Displaying information Calling the Information setting window With this function the model designation, serial number, resolution, H/V frequency, input signal and polarity of the synchronisation signal are displayed. Notes on ergonomic colour adjustment If you select colours for the display in your application programmes, take note of the information below.
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Troubleshooting Should an error occur, first check the following points. If the distortion is still not eliminated, the monitor should, if possible, be checked on another computer. If you are unable to solve the problem, please inform our help desk.
Page 31
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Having this problem? Check the following points: Picture is wrongly adjusted ► Press the SELECT/MENU button to activate the function Factory Recall. The Auto Processing message is displayed. Picture disturbances (vertical lines) ►...
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Notes regarding the DIN EN ISO 13406-2 standard Permanently unlit or lit pixels The standard of production techniques today cannot guarantee an absolutely fault-free screen display. A few isolated constant lit or unlit pixels (picture elements) may be present. The maximum permitted number of pixels faults is stipulated in the stringent international standard ISO 13406-2 (Class II).
VGA interface, it can automatically read the data for ensuring optimum operation from your monitor and select the appropriate settings. If the monitor SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S is not yet displayed in the list of monitors, you can select the following monitor instead:...
SCENICVIEW P17-2 / P19-2 / P19-2P / P20-2 / P20-2S Pin assignment D-SUB Meaning Meaning Video input red +5 V (DDC) Video input green Sync. earth Video input blue Earth Earth DDC-Data Earth H. sync Red video earth V. sync...